84000 SERIES ILLUMINATED SWITCHES
Lever-LiteŽ III illuminated lever switches are designed for front-of-panel mounting,
relamping, terminating and removal. A minimum of time is required to install singly, in rows, or in matrix arrays to meet a wide variety of switching applications. Mounts on .875 inches (22.22 mm) horizontal centers or 1.5 inches (38.1 mm) vertical centers. Talk-listen (intercom) function is also available.
LAMPS
Standard T-1 3/4 inch midget flange-base lamps (not supplied) are available in voltages up to 28V.
SPECIAL ORDER FEATURES
1. Talk-Listen (Intercom) function.
2. Welded cross bar gold alloy for dry circuit and silver contacts are available.
ILLUMINATION
A single internal lamp provides brilliant lever lighting in any color required. Standard factory installed color filters are provided as follows: Series 84000, Multi-Color Illumination 2-position - Amber (neutral position); green (down position). 3-position - Red (up position); amber (neutral position); green (down position). One-color (all positions) and non-illuminated switches can be specified on special order. Switchcraft will install filters for non-standard illumination requirements at nominal cost on special order.
MOUNTING
Grasp fingernail slots on opposite sides of escutcheon and snap out. Next, grasp lever and pull lever assembly free. Insert switch into panel hole.
Turn two internal screws clockwise with screwdriver to securely mount switch to panel.
Replace lever assembly and "snap" escutcheon into place. Installation complete!
RELAMPING/REPLACING COLOR FILTERS
Lever-Lite III switches are designed for simplified lamp installation and replacement, and color filter changes or custom installation in the field or on the OEM production line. Lamps and filters may be changed at any time with ease and without dismounting switch from panel or disturbing wiring.
Remove escutcheon and lever assembly. (see "MOUNTING" above) For relamping, pull lamp out of retainer with finger-tip. Replace lamp.
For color filters, use fingernails or small screwdriver to remove. Gently lift (don't pry) up under edge of filter until it "pops" out.
Place new filter in position and press until it "snaps" in. Replace lever assembly and escutcheon. (see "MOUNTING" above)
SPECIFYING LEVER-LITEŽ III SWITCHES
1. Basic Switch - Refer to Part Number table for ordering switches. For special switches, such as talk-listen (intercom) function, special circuit forms, or non-illuminated switches, contact factory for price and delivery.
2. Illumination - Supplied with standard color filters installed.
3. Lamps - Lamps are not supplied with switches.
PART NUMBERS
TWO POSITION |
| Part Numbers |
Switching
|
Non-Locking
|
Locking
|
| - |
84206L
|
2-C
|
| - |
84212L |
4-C |
| THREE POSITION |
| |
|
Position 1
|
Position 2
|
-
|
84306L
|
1-C
|
1-C
|
-
|
84312L
|
2-C
|
2-C
|
| - |
84324L |
4-C |
4-C |
| Special order only; contact Switchcraft. |
SPECIFICATIONS
Mounting/Retaining Clips and Covers: Steel, plated.
Contact Ratings:
Welded cross bar palladium contacts rated at 1A, 200W maximum AC non-inductive load are standard. Other contacts available.
Springs: Copper alloy, plated.
Lamp Terminals:
Copper alloy, plated.
Lamp Socket: Zinc, plated.
Terminals: Copper alloy, plated, straight solder lugs.
Housing, Escutcheon, Knob, Actuator and Switching Stacks Insulation: Molded plastic.
Temperature Range:
-22°F to 158°F (-30°C to +70°C).
Dielectric Strength: 1 kV DC.
Leakage Resistance: 1,000 M(omega) or greater.
REPLACEMENT LEVER
Number G6083 (for locking lever)
click here to download a schematic
drawing
(you will need to have Adobe Acrobat installed on your system to do this)
